POCKET DOSIMETER and Charger
Direct-Reading Dosimeter – W138, 0-200mR with Sapphire Window
The Direct-Reading Dosimeters are rugged, precision instruments. They are designed to measure and directly read, at any time accumulated dose of gamma and x-ray radiation exposure. The Direct-Reading Dosimeter is designed to satisfy military specifications for the IM-Series RADIAC METER and ANSI N13.5 and N322 requirements. The sturdy metal clip attaches the dosimeter to a pocket or any object to monitor total radiation exposure. They are hermetically-sealed and immersion proof.
The Direct-Reading Dosimeter is a pocket-size, carbon-fiber electroscope with an ion chamber for detecting and indication of integrated exposure to Gamma and X-Ray radiation. It has a thin wall which permits the penetration and detection of radiation. This model comes with a hardened sapphire window that won’t scratch even in the toughest of conditions.
Dosimeters are extremely sensitive instruments. Although they are constructed for rugged use, they should receive the same care as a wristwatch. Since dosimeters are hermetically sealed at the factory, they cannot be repaired or adjusted in the field. Therefore, if instrument malfunctioning is experienced, the instrument should be returned to the factory or your dealer. Dosimeters may be maintained in operating condition simply by cleaning the eyepiece lens and the charging switch insulator with clean water and a cloth that is free of lint and grit. Make sure the charging switch insulator is absolutely free of lint and moisture at all times. Caution: Do not insert any sharp objects into, or tamper with parts in the charging switch recess. Irreparable damage may be done.
|Radiation Detected :||Gamma and X-Ray from 16 keV to 6 MeV|
|Detector: Fiber-||: Electrometer mounted in an Electrically Conductive Plastic Ion Chamber|
|Detector Housing||: Very low permeability plastics – Hermetically-Sealed|
|Accuracy||: +/– 10% of true exposure|
|Rate Response||: Dose rate independent for Gamma and X-Ray|
|Electrical Leakage||: Less than 1.0% of full scale for 24 hours at 50 C|
|Temperature Range||: -20 degrees C to +50 degrees C|
|Relative Humidity||: Up to 90%|
|Dimensions||: 4.5” (12.4 cm) Length X .6“ (1.5 cm) Diameter|
|Weight||: 1.0 oz. (25 grams)|
|Finish||: Natural Matte Black with a Metal Clip|
|Shelf Life||: 20 Years|
|Specifications||: ANSI N13.5 and ANSI N322-1997|
To read a dosimeter, place it on the charging contact and switch on the light. Do not press harder than necessary to avoid loss of reading.
To charge a dosimeter, press it down on the charging contact with sufficient force to bring the dosimeter body in contact with the charging assembly .The charger charging contact is spring loaded and has a positive mechanical stop. This design feature makes it virtually impossible to damage dosimeters through excessive charging force. This will provide sufficient force to actuate the charging switch in the dosimeter. Now read the dosimeter and adjust the control Knob until the dosimeter indicates zero. Remove the dosimeter from charging contact.
When the dosimeter charger is not in use, remove the batteries, clean the batteries contacts if they appear corroded prior to further use.
- Capable of charging any pen type pocket dosimeter
- Conforms to ANSI,N42.6-1980
The Radiological dosimeter charger supplies the voltage required to charge or zero quartz fiber dosimeters . A transistor oscillator converts the direct current from a flashlight battery to alternating current so that the transformer can step up the battery voltage 3v to 220v required by the dosimeter. A voltage regulator is used to adjust the output voltage to the exact value required to bring the dosimeter to read zero.
|Size||65 X 25 X 130 mm|
|Controls||One Turn Potentiometer|
|Operating Conditions||0- 50° C 90% Humidity|
|Battery||AA Alkaline Battery 2 No’s|
RADIOACTIVITY WARNING BLINKER WITH SIREN
VARIOUS MODEL AS PER YOUR REQUIREMENT…This is a device to warn against radioactive rays within the area by setting the boundary of the Radioactive area or restrictive area for the radioactive penetration inspection or to alert other outside personnel to evacuate the area.
|Warning Flashing Light, Siren with Volume Control. No detector for Radiation||Works on
230 V Mains
|Warning Blinker Light with siren Volume Control. Built in Radiation Detector for Radiation. Automatically Switches on – when Radiation intensity exceeds 5mR/Hr.||Works on 230 V mains. Also works on Built in Battery. Charging unit built in the system.|
|Small In Size|
|Easy to Use|
|The Flashing light and Siren will automatically switch on when the radiation level exceed the pre-set level set at the factory.|
|The preset limit set at the factory is 5 mR.|
|It can be changed as per your requirement.|
|Warning Flashing Light, Siren with Volume Control. No detector for Radiation.||Works on|
|Also provided with 4 x corded lamps. The corded lamps can be hung on 4 corners to cordon off the radiation area.||230 V Mains|
|Length of cord: 5 M|
|Warning Flashing Light, Siren with Volume Control..||Works on|
|No detector for Radiation||230 V Mains. Also works on Built in Battery.|
|Battery-operated, small in size. It can be operated for 8 hours with one charge.||Charging unit built in the system.|